Planet Technology FGSW-2402PVS Uživatelský manuál Strana 1

24-Port 10/100Mbps PoE + 2-Gigabit Web Smart Ethernet Switch FGSW-2402PVS FGSW-2620PVS User’s Manual

6  Note: When choosing a location, please keep in mind the environmental restrictions discussed in Chapter 1, Section 4, Specification. Step4:

7 Figure 2-5 Mounting the Switch in a Rack Step6: Proceed with the steps 4 and steps 5 of section 2.2.1 Desktop Installation to connect the network

8 #'0!)& Unlike the unmanaged switch, FGSW-2402PVS/ FGSW-2620PVS performs series smart functions tha

9 Figure 3-2 Power-up System Self-diagnostic screen "'After the self-test completes successfully, the screen in figure 3-3 appea

10 Figure 3-4 Main Menu Screen 1. Port Status Display the port status, which allow you to view the port disable/enable status, current link status

11 Figure 3-5 Port Status Screen O Object Description Port Indicate port 1 to port 24, and 2-module slot. Enable Display

12  Note: 1. xx represents the maximum fiber-optic distance, for example MII-L40 for 40kilometers. For the available models, please consult yo

13 Object Description VLAN Configuration Allow user to disable/enable the Port-based VLAN function. The available options are shown as below

14 Figure 3-12 Create a port-based VLAN Group screen Press “Enter” then the following screen in figure 3-13 appears. Figure 3-13 Create a port-ba

15 Figure 3-16 Create a port-based VLAN Group completed screen 3.2.6.2 Edit a VLAN Group Use the "TAB" key to move the highlight to the &l

2 Trademarks Copyright  PLANET Technology Corp. 2005. Contents subject to revision without prior notice. PLANET is a registered trademark of PLANET

16 3.2.6.3 Delete a VLAN Group Use the "TAB" key to move the highlight to the <Delete> and press "Enter" to start the del

17 Figure 3-24 Delete existence VLAN Group successfully Screen 3.2.6.4 Return to Main Menu Choose “Return to Main Menu” to return to Main Menu scre

18 Monitoring Port Allow seeing all monitor port traffic; you can connect Monitoring port to LAN Explorer, Session Wall, Sniffer Pro or Netxray. Mo

19 After setup is completed. Press "ESC" key to return to Actions menu and use the "TAB" key to choose the <Save> for savin

20 ,%Press 8 on your keyboard or use the "TAB" key to move the highlight to the Misc Configuration and press “Ent

21 O Object Description Broadcast Strom Filter If this function enable, the Switch will limitation the broadcast packe

22 O Object Description Password protection Allow user to disable or enable the password request of the console and W

23 Figure 3-39 Reboot Switch Screen Figure 3-40 Switch Console Login Screen 3.2.10.4 Reboot System Press 4 on your keyboard or use the "TAB&

24 Figure 3-43 Switch Console Login Screen 3.2.10.5 System Information Press 5 on your keyboard or use the "TAB" key to move the highlig

25 After setup is completed. Press "ESC" key to return to Actions menu and use the "TAB" key to choose the <Save> for savin

3 TABLE OF CONTENTS 1. INTRODUCTION...

26 O Object Description POE Ports Config Allow user to configure the POE function and power provision priority. Ple

27 O Object Description Port List the port number for configuration. Enable List each port POE power provision settin

28 "*08!)& The Web Smart Ethernet Switch provides a Web interface for Switch Smart function conf

29 Port Configuration: Allow user to disable/enable each port, Auto-negotiation disable/enable on each port, per port 10/100Mbps full and half duplex

30 Figure 4-4 Port Configuration Screen After setup is completed. Press "Apply" button for save the current configuration. The screen fi

31 "/-'&%This function allows to enabling the port-based VLAN function. The screen in figure 4-8 appears. Figure 4-8

32 Figure 4-11 VLAN Configuration save successfully Screen Press “Back” for back to previous web screen. It also support delete the existence VLAN

33 Figure 4-14 Port Mirroring Configuration save successfully Screen Press “Back” for back to previous web screen. "56#%This

34 Figure 4-17 QoS Configuration Screen After setup is completed. Press "Apply" button for save the current configuration. The screen in

35 Figure 4-20 Bandwidth Control save successfully Screen Press “Back” for back to previous web screen. ",%This function

4 5.1 ADDRESS TABLE...

36 Figure 4-22 Broadcast Storm Filter Screen Collision Retry Forever: If this function is disabled, when a packet meet a collision, the switch wil

37 Figure 4-26 Console Auto Logout Time Screen Web Auto Logout Time: Allow user to set the Auto logout time of web interface. The available options

38 The screen in figure 4-29 appears. Figure 4-29 Password Setting Screen If disable the password protection. Then the following screen appears.

39 Figure 4-32 Password Setting save successfully Screen Press “Back” for back to previous web screen. ",#93%#Thi

40 Figure 4-35 System Information Screen ",/%This function allows modifying the IP address, subnet mask and default gatew

41 POE Port Status: Allow user to check the port Power over Ethernet settings and the connected power usage. Please refer to section 4.11.2. "

42 "'This function allows to logout the web interface of the Switch. The screen in figure 4-41 appears. Press “OK” then the web

43 2#*0& 2& :The Switch is implemented with an address table. This address table composed of many entries. Each

44 /8'0#) This chapter contains information to help you solve problems. If the Ethernet Switch is not functioning properly, make

45 &0<& &#=>+"2&3 1000Mbps, 1000Base T Contact MDI MDI-X 1 BI_DA+ BI_DB+ 2 BI_DA-

1   Check the contents of your package for following parts: 24-Port 10/100Mbps PoE + 2-Gigabit Web smart Switch x

46 Figure A-1: Straight-Through and Crossover Cable Please make sure your connected cables are with same pin assignment and color as above picture

2  2 10/100/1000Mbps ports and 2 SFP interfaces (FGSW-2620PVS only)  Auto-MDI/MDI-X detection on each RJ-45 port  Prevents packet loss with

3 QoS Allow to assign low and high priority on each port Bandwidth control Allow to assign rate control on each port PoE Configuration Allow to E

4  #&''& This section describes the functionalities of FGSW-2402PVS/ FGSW-2620PVS components and guides how to install i

5 LED Color Function LNK/ACT Green Lit: indicate the link through that port is successfully established. Blink: indicate that the switch is actively