Planet-technology VC-200S Uživatelský manuál

VDSL2 Router VC-200M / VC-200S User’s Manual

PHONE The RJ-11 connector allows voice communication between the router and phone through a twisted-pair phone wire. VDSL2 The RJ-11 connector allo

VC-200S. II. Uses the supplied RJ-11cable connects to VC-200M or VC-200S with your phone company. Step 2. Connect a Workstation to the Router'

3. In the Local Area Connection Status window, click Properties. 4. Select Internet Protocol (TCP/IP) and click Properties.

5. Select the Obtain an IP address automatically and the Obtain DNS server address automatically radio buttons. 6. Click OK to finish the configura

4. Select Internet Protocol (TCP/IP) and click Properties. 5. Select the Obtain an IP address automatically and the Obtain DNS server address autom

3. Select the Obtain an IP address automatically radio button. 4. Then select the DNS Configuration tab. 5. Select the Disable DNS radio button an

3. Select the Obtain an IP address from a DHCP server radio button and click OK. Note: By factory default: DHCP is disabled, Device Mode is Bridge

Chapter 3 Configuration 3.1 Determine your connection settings Before you configure the router, you need to know the connection information supplie

3.3 Configuring with Web Browser It is advisable to change the administrator password to safeguard the security of your network. 1. To configure t

Step1- Click “Bridge Mode” in VC-200M and VC-200S, and then press “APPLY” to submit setting. Step2- Select profile in VC-200M and VC-200S, we sugg

Copyright Copyright© 2008 by PLANET Technology Corp. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, s

Step3- Click “Active” to make the connection is ready. Step4- After successful connect between VC-200M and VC-200S, the information will show on c

Router Mode Step1- Click “Router Mode” in VC-200M and VC-200S, and then press “APPLY” to submit setting.

Step2- Change LAN IP address, e.g. VC-200M is 192.168.1.100, VC-200S is 192.168.99.100. Step3- Select WAN IP address, e.g. we set WAN to the Static

Step4- Fill in WAN IP address, e.g.VC-200M is set 10.1.1.100, VC-200S is 10.1.1.200, and gateway address should point each other. Step5- Select profi

Step7- After successful connect between VC-200M and VC-200S, the information will show on channel status. Note: Please reference the throughput tes

2. Advanced Setup- Advanced setup features allow the user to configure all the functions that are supported by VC-200M/VC-200S like routing, and UPnP

3.5.3 System The System link can be viewed in the left navigation bar. The following are the options available under system, show as below. z Host N

The screen contains the following details: Filed Description Host Name Enter the host name of the VC-200M/VC-200S. Domain Name Enter the domain nam

z Click “APPLY” to save the information that has been entered. 3.5.3.3 Administrator Settings To add a user or change user’s password, click on the Ad

Note: By factory default: Device Mode is Bridge Mode. 3.5.3.5 Firmware Upgrade To update the system firmware, click on the Firmware Upgrade link in t

FCC Caution: To assure continued compliance (example-use only shielded interface cables when connecting to computer or peripheral devices). Any chan

z Click “Release” to release IP Address for the WAN interface. z Click “Renew” to renew the IP Address for the WAN interface. 3.5.3.7 System Logs T

The screen contains the following details: Filed Description Log File This lists all the system events. z Click “Download” to download the log file

3.5.4 WAN The WAN settings can be viewed in the left navigation bar. The following are the options available under WAN, show as below. z Dynamic IP z

The screen contains the following details: z Click “APPLY” to save the information that has been entered. z Click “CANCEL” to exit from this page.

The Screen contains the following details: Filed Description IP Address assigned by your ISP Enter the IP Address of VC-200M/VC-200S. Subnet Mask Ent

MTU Enter the maximum connection units of the PPPoE. The MTU range is 1400 to 1492 bytes, by factory default is 1492. Maximum Idle Time This is the p

The screen contains the following details: Filed Description Domain Name Server(DNS) Address Enter the DNS address of the primary DNS server. Secondar

3.5.5.1 LAN Setting To configure the LAN interface, click on the LAN Setting link in the left navigation bar, show as below. The Dynamic Host Co

IP Pool Ending Address Enter the ending IP Address of the DHCP server. (When Enable DHCP Server) Lease Time Select the lease time of the DHCP server.

The NAT Settings can be viewed in the left navigation bar. The following are the options available under NAT, show as below. z Virtual Server z Port

Revision User’s Manual for VDSL2 Router Model: VC-200M / VC-200S Rev: 2.0 (March 2008) Part No. EM-VC200

The screen contains the following details: Filed Description Private IP Enter a private IP Address of specified entry. Private Port Enter a privat

The screen contains the following details: Filed Description Server IP Enter the IP Address of a specified local machine. Mapping Port Assign a ran

The screen contains the following details: Filed Description Enable Enable or disable the DMZ setting of VC-200M/VC-200S.Select the check box to en

3.5.7.1 Static Route The static routing function determines the path that data follows over your network before and after it passes through your route

PC2 can go to Internet through VC-200M/VC-200S, so please reference as below to fill in static routing table. Interface: LAN Destination IP: 203.67.3

3.5.8 UPnP UPnP (Universal Plug and Play) is a distributed, open networking standard that uses TCP/IP for simple peer-to-peer network connectivity b

The screen contains the following details: Filed Description Enable UPnP To enable or disable UPnP Setting. Select the check box to Enable or Disable

4.1.1 Channel Configuration To set direction, Min Data Rate, Max Date Rate, and Max Interleve Delay of channl1, click on the ChannelConfig in the left

4.1.2 Line Configuration Signal-to-Noise Ratio, often written S/N or SNR, is a measure of signal strength relative to background noise. The ratio is u

The screen contains the following details: Setting Description Direction Select the target direction of downstream or upstream. Target SNRM Set t

Table of Contents CHAPTER 1 INTRODUCTION...7 1.1 Feature...

frequency bands. Table 1 list 8a, 8b, 21a, 12b, and 17a standard VDSL2 profile about the bandwidth, tones, tone spacing, and line power. <Table 1&

Note: By factory default is VDSL2 Profile 17a-Bandplan ITU AnnexB_B12. 4.1.4 Active To enable or disable VDSl2, click on the Active link in the left

4.1.6 Version Information To view the version information is about Web UI, API Library, Chipset FW, Chipset HW, and DSL Driver.

Appendix A Field Throughput for VDSL2 profiles Router Mode Band Profile Distance 8a, 8b 12a, 12b 17a 400 Meter (1312 feet) 20 / 5 15 / 15

Appendix B Glossary DHCP DHCP stands for Dynamic Host Configuration Protocol. This protocol automatically configures the TCP/IP settings of every co

Internet Service Provider. An ISP is a business that provides connectivity to the Internet for individuals and other businesses or organizations. LAN

56TCP/IP Transmission Control Protocol/Interne

3.5.5.1 LAN Setting...37 3.5.5.2 DHCP Client List...

Chapter 1 Introduction The PLANET VDSL2 Router, VC-200M / VC-200S is based on two core networking technologies: Ethernet and VDSL2 (Very High Speed Di

 Selectable VDSL2 transmission modes. User can choose transmission modes (8a,8b,12a,12b,and 17a) through management interface on VC-200M / VC-200S

Front Panel LED definition LED State Description ON When the router is powered on, and in ready state. PWR OFF When the router is powered off. Flas